DE
AGABEK2P3Combination filter, RD40

Combination filter ABEK2P3 with RD40 thread

The filter with the widest coverage in the AirGuard Pro range: gas filter A, B, E and K in class 2, combined with P3. For the full-face mask AG700 at workplaces with mixed hazardous substances up to 0.5 % by volume.

Marking
A2B2E2K2P3
Standard
EN 14387:2021
Connection
RD40
Fits
AG700
PPE category
III, CE 2834
Packaging
20 pieces
View in the B2B shopRequest a quoteRequest samples

Data sheet (PDF)Instructions for use (PDF)Ask for advice

Warnings

  • Replace gas filters according to a change schedule, at the latest when odour, taste or irritation is noticed. Then leave the area immediately.
  • Do not use filters containing activated carbon for firefighting, near open flames or with molten metal splashes.
  • Filters do not supply oxygen: do not use where the oxygen content may be too low (below 19.5 % by volume according to the instructions for use), in tanks, pits, shafts and confined spaces, or if the substance and its concentration are not known.
  • Use only with the AirGuard Pro masks named in the documents.

The instructions for use of the product are authoritative.

AirGuard Pro Combination filter A2B2E2K2P3 AGABEK2P3, black

Gases, vapours and particles

The combination filter protects against organic gases and vapours (boiling point above 65 °C), inorganic gases, acid gases, ammonia and amines up to 0.5 % by volume and at the same time retains dust, smoke and mist. With the full-face mask AG700 it is permitted up to 400 times the workplace exposure limit under DGUV Rule 112-190.

Not covered are carbon monoxide, mercury, nitrous gases and organic substances with a boiling point up to 65 °C.

Replacement

Replace according to a change schedule, at the latest at odour, taste or irritation, and when breathing becomes noticeably harder. According to the instructions for use the filter can be kept airtight until the next shift. More under Changing filters.

Using correctly

  1. 01

    Open only at the place of use

    Take the filter out of its packaging immediately before use and check the expiry date on the filter.

  2. 02

    Screw in centrally

    Keep the side connections of the AG700 closed and screw the filter clockwise into the RD40 thread until tight.

  3. 03

    Check the face seal

    Place the palm of your hand over the exhalation valve and exhale slowly. If air escapes at the edge of the mask, reposition it and tighten the straps. Before every use.

  4. 04

    Replace in good time

    According to the change schedule, at the latest when odour, taste or irritation is noticed. Replace the filter too if breathing becomes harder.

When filters are replaced

Technical data

Technical data AGABEK2P3
Article numberAGABEK2P3
TypeCombination filter
Colourblack
StandardEN 14387:2021
MarkingA2B2E2K2P3
Gas filterType A, B, E and K, class 2 (up to 0.5 % by volume)
Particle filterP3
ConnectionRD40 thread, one filter
FitsAG700
PPE categoryIII under Regulation (EU) 2016/425
Notified bodyCCQS Certification Services Limited, 2834
Packaging20 pieces, each in a box

Downloads

Declaration of conformity on request: Request documents

Frequently asked questions

What does A2B2E2K2P3 mean?

Gas filter types A, B, E and K, each in class 2 (up to 0.5 % by volume), plus a P3 particle filter.

Is ABEK2P3 always the best choice?

No. It covers the most, but is only for the full-face mask AG700. Where only particles or only one gas group occur, a targeted filter is often lighter and cheaper. The respirator finder shows the alternatives.

Does the AGABEK2P3 fit the half mask?

No, only the RD40 thread of the full-face mask AG700. For the half mask there is the AGABEKK1P3 (class 1) with bayonet.

Goes with it

To the respirator finder

The brand family of DS SafetyWear Arbeitsschutzprodukte GmbH